Chain Plate Conveyors
Chain Plate Conveyors: Slat and Chain Selection
Chain plate conveyors survive heat, oil and impact that destroy belt conveyors. They also fail early when the slat pitch, the chain…
4 min read
Capability
Products
Conveyor systems and process equipment engineered to the workpiece, the takt time and the floor plan — from a single speed chain loop to a complete assembly floor.
Explore Products
8 sections
01
Speed Chain Conveyor Lines
2.5x speed, free accumulation
4 articles
02
Powered Roller Conveyors
Cartons, totes and pallets
3 articles
03
Belt Conveyor Systems
PVC, PU and food-grade belting
3 articles
04
Chain Plate Conveyors
Hot, heavy and oily parts
3 articles
05
Overhead Conveyors
Coating, drying and plating
3 articles
06
Assembly Lines
Balanced stations, fixtures, takt
3 articles
07
Industrial Ovens & Drying Lines
Batch and tunnel drying
3 articles
08
Workbenches & Tooling
ESD benches, jigs and racks
3 articles
Belt Conveyor Systems
Belt Splice Methods: Vulcanised, Mechanical and Finger Splice
The splice is the weakest point on any belt and the first place a food safety auditor looks. Selection depends on belt type, pulley…
3 min read
Powered Roller Conveyors
Zero-Pressure Accumulation: Zone Logic, Sensors and Timing
Zero-pressure accumulation fails for the same three reasons on almost every line: sensor placement, zone length against pallet…
3 min read
Speed Chain Conveyor Lines
Speed Chain or Roller Conveyor? Choosing for High-Mix Assembly
Both conveyor types can move a carrier at the same rate. The difference appears when the product changes every few hours, when…
4 min read
Industrial Ovens & Drying Lines
Batch Oven or Tunnel Oven? Matching the Dryer to the Process
The choice between a batch chamber and a tunnel line is set by product mix, throughput and the process window — not by the price of…
4 min read
Chain Plate Conveyors
Curves and Transitions on Chain Plate Conveyors
A curve is where a chain plate conveyor is most likely to jam, tip a product or wear a chain. The geometry, the slat width and the…
4 min read
Workbenches & Tooling
Fixture Plate Design: Location, Material and Quick Change
A fixture plate is a precision interface between the product and the line. If the location scheme is wrong, no amount of clamping…
4 min read
Belt Conveyor Systems
PVC, PU or Food-Grade Belting: Five Operating Conditions Compared
Belt material is usually chosen from habit. Five operating conditions — temperature, oil, abrasion, cleaning and static — separate…
5 min read
Overhead Conveyors
Accumulation Stops and Hanger Design for Overhead Chain Systems
An overhead line that cannot accumulate is a line that stops whenever an operator stops. Stops and hangers are a pair; designing…
5 min read
Assembly Lines
Fixtures, Tooling and Material Feed at Takt
A balanced line still loses output if the fixture takes nine seconds to load or the operator walks four metres for a part. Tooling…
5 min read
Speed Chain Conveyor Lines
Setting Cycle Time on a Speed Chain Line: Stations, Accumulation and Buffer
Takt time is a division. Line balance is where the work actually happens. Here is how to divide stations, size buffers and avoid a…
5 min read
Workbenches & Tooling
ESD Workbench Specification: Configuration and Acceptance
An ESD workbench is a system: surface, frame, grounding, wrist strap and seating. Buying an anti-static mat and putting it on a…
4 min read
Powered Roller Conveyors
Gear Motor, Drum Motor or Chain Drive? Choosing a Roller Conveyor Drive
Three drive architectures dominate powered roller conveyors. The right choice depends on width, speed, washdown, maintenance access…
5 min read
Chain Plate Conveyors
Chain Plate Conveyors in High-Temperature and Heavy-Duty Service
Chain plate conveyors survive where belt and roller conveyors fail: hot parts, oily parts, heavy castings and washdown. The design…
5 min read
Industrial Ovens & Drying Lines
Industrial Oven Temperature Uniformity: Test Method and Airflow Design
A uniformity claim is only meaningful with a test method attached. Nine-point measurement, a loaded chamber and a defined…
4 min read
Belt Conveyor Systems
Belt Tracking Problems: Seven Causes and How to Correct Them
A belt that runs off to one side is usually complaining about alignment, tension or load placement. The fix is rarely to tighten…
5 min read
Speed Chain Conveyor Lines
Speed Chain Conveyor Lines: Structure, Working Principle and Selection
A speed chain line is not a roller conveyor with a different name. The 2.5× ratio between chain and carrier speed changes how you…
6 min read
Overhead Conveyors
Overhead Conveyors in Coating and Drying Lines
An overhead conveyor is the spine of a paint or powder line. Hanger design, grounding, oven transitions and accumulation decide…
5 min read
Powered Roller Conveyors
Roller Conveyor Speed and Pitch: A Practical Calculation Method
Two numbers decide whether a roller conveyor works: the surface speed at the roller and the gap between rollers. Both can be…
5 min read
Assembly Lines
Line Balancing: A Practical Method for Station Division
Line balancing is not a software exercise. It is a sequence of decisions about what can be separated, what must stay together and…
4 min read
Specification help
Not sure which configuration fits?
Describe the product, the rate and the constraint that worries you. We will tell you what the line needs — and what it does not.